Telus Modem IR1200 Instrukcja Użytkownika Strona 48
- Strona / 54
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
TELUS Mobility™
42 www.telusmobility.com
Supported S-Registers
The following table outlines the list of S-Registers that can be used to customize your modem.
Register # Function
0 Automatic Answer. Determines if the modem automatically answers incoming calls.
• If the value assigned to this register is 0 (zero), the modem does not answer the call but
sends an appropriate message to the computer that commands the modem to answer the
call.
• If the value assigned to this register is a non-zero, the modem answers the call without
waiting for the computer to issue its answer-call command.
Valid value ranges from 0 (zero) to 255. 0 (zero) is the default value.
2
Escape (ESC) Code Character. Specifies the ASCII character to be used to escape from
either data or online mode to command mode.
Valid value ranges from 0 (zero) to 127. 43 or the ASCII plus (+) key is the default value.
3
Command Line Terminating Character. Specifies the ASCII character to be used to
terminate a command line without carrying out any command that might be issued.
Valid value ranges from 0 (zero) to 127. 13 (which represents the ENTER (PC Compatible)
or RETURN (Macintosh) key) is the default value.
4 Response Format Character.
Valid value ranges from 0 (zero) to 127. 10 is the default value.
5 Command Line Editing Character.
Valid value ranges from 0 (zero) to 127. 8 (representing the Backspace key) is the default
value.
6 Pause Before Blind Dialing.
Valid value ranges from 2 to 10. 2 (seconds) is the default value.
7 Connection Completion Timeout.
Valid value ranges from 0 (zero) to 255 seconds. 120 (seconds) is the default value.
8 Command Dial Modifier Time.
Valid value ranges from 0 (zero) to 255 seconds. 2 (seconds) is the default value.
10
Automatic Disconnect Delay. Determines the amount of time between loss of carrier and
disconnection of the data call.
Valid value ranges from 1 to 254 tenths of a second. 14 (1.4 seconds) is the default value.
12
Escape Code Timer. Determines the time duration within which the escape code must be
sent by the computer to escape from online command mode. The time (in seconds) the
modem waits is determined by dividing the specific register value by 50.
Valid value ranges from 20 to 255. 50 or 1 second (50/50) is the default value.
30
Idle Timeout. Determines the amount of time that the modem waits in online mode for a
command from the computer before disconnecting the call and returning to command
mode.
Valid value ranges from 0 (zero) to 255 seconds. 0 (infinite time period) is the default
value.
- CONFIGURATION GUIDE 1
- TABLE OF CONTENTS 3
- TABLE OF FIGURES 7
- FCC COMPLIANCE 8
- INTRODUCTION 9
- Customer Care 10
- OVERVIEW 11
- Modem Specifications 12
- MODEM CONFIGURATION 14
- Windows NT/2000 15
- Verify Dial-Up Networking 15
- • Packet Data enter: s=2 16
- Packet Data Applet 17
- Installing iDEN 17
- • Baud Rate: 19200 (bps) 20
- TELUS Mobility™ 26
- Manual Modem Configuration 27
- Install the Modem 28
- Configure the Modem Driver 29
- Modem Profiles and Settings 33
- Configuring with AT Commands 33
- AT COMMAND REFERENCE 36
- Dial [ATd] 37
- Hang-up [ATh] 37
- Go Online [Ato] 38
- Pulse Dialing [Atp] 38
- Quiet Mode [ATq] 38
- Tone Dialing [ATt] 38
- Verbose Result Codes [ATv] 38
- Extended Result Codes [ATx] 39
- Restore User Defaults [Atz] 39
- DCD Behavior [AT&c] 39
- DTR Behavior [AT&d] 40
- Local Data Rate [AT+ipr] 42
- SLIP MTU [AT+wv312] 43
- DTE Stack [AT+ws45] 44
- WDS Stack [AT+ws46] 45
- Service Class [AT+fclass] 45
- S-REGISTERS 47
- Supported S-Registers 48
- TROUBLESHOOTING 49
- Error Messages 50
- Diagnostic Commands 50
- Extended Error AT Command 51
- Extended Error Result Codes 51
- Code General Description 52
- SAFETY NOTICE 53
Samsung HW-J6001 manuels
Manuels d'utilisation et guides de l'utilisateur pour Lecteurs de CD Samsung HW-J6001.
Nous fournissons des manuels en pdf Samsung HW-J6001 à télécharger gratuitement par type de document :
Komentarze do niniejszej Instrukcji